Intelligent light bulb with the birth of intelligent

According to INLIFE reports, speaking of smart bulbs, the market has been able to become some of the color you want, App control switches and other functions. But in fact, these are pseudo intelligence function, must be artificially changed or set in advance. Today, however, this i-light DOUBLE is also known as smart bulbs, then it is how intelligent it? Below I take you to experience together.

From the packaging point of view, in addition to the above LED bulb pictures and text, the other really can not see this is a light bulb products. When you open, you will see three schematic parallel discharge. They are sensors, LED lights and power adapter. The three things were all packed in kraft paper. We take out the inside of the object, the contents of the sensor 2, power adapter, the junction of the 1, LED lights with a circle of the 2, small cloth, as well as small pieces of the package, there are 1 of the 1.

Apart from these objects, the sensor volume is relatively small, prominent part of the sensor head, can be induced to 120 degrees for the range of light changes or personnel movement. The back of the sensor, there will be a time of adjustment, which is to control the LED lights light lasting time, the default is 30 seconds, we can also be adjusted to 10 minutes. In addition, the groove is used for fixing.

There is nothing special about the power adapter and the divider, and here's a picture.

The LED lamp with a circle, one is a circular connection port, the other is the LED lamp belt. The lamp belt can be adjusted according to the needs of their own length, it is the back of the 3M double-sided adhesive layer. Close look at the lights can be seen on the distribution of a lot of light-emitting diodes, that is, LED, and resistance. This lamp is made of transparent rubber, so the texture is very soft, so we do not need to worry too much about the turn of the corner when turning on the lamp with a low degree of adhesion.

Small package inside which are fitted with two wire clips and sensors. They are used for fixing wires and sensors.

After the introduction of these objects, we will enter the installation link. The installation of this smart bulb is not difficult, but we need to install their own position to conceive. We start with the connection, one end of the power adapter is connected to one end of the distributor, and the side of the divider is respectively connected with the inductor and the LED lamp belt.

Connect later, the installation guide suggested that we need to install clean and wipe the surface, then here we put rotary buttons and sensors on the card, as long as the fastening groove and the convex sensor and knob can. Then tear open the back of the 3M double-sided adhesive protective layer, affixed to the need to install the position. Here to remind you, choose the location of the sensor installation, as far as possible to choose a sensor to allow people to feel the movement or can directly feel the location of the ambient brightness, the installation guide is also a recommended location. I'm going to install it under the table.

Then install the LED lamp with the same clean and clean the surface after the installation, I choose LED lights installed on the desktop around the side of the installation, at the same time, the side broke 3M double-sided adhesive protective layer with behind the lamp. This can be easily installed along the edge of the. If the length of the protruding part can be cut with scissors.

After installation of these, found that these are 00 pieces of wire, we can use two bar clamp connection is fixed, so the wire will not loose, so both beautiful and safe.

The end of the installation here, and then we plug in the power, turn off the ambient light, the LED light immediately lit up. Here, we will ask, what is special? I-light in the end where intelligence? The key is in the sensor, the sensor can sense the surrounding environment light change, when we close the ambient light brightness change down, sensors will be able to control the LED lights open, this time we continue opening can be adjusted, above the painting. In addition, the brightness of the LED lamp is also based on the actual situation to change, this intelligent regulation to a certain extent can save electricity. Then, when there are people walking around, the sensor can also be adjusted according to changes in the LED lamp switch, so that people go out the lights. This product design ideas, is to let the LED lights can be automatically turned on or off, rather than the need to artificially adjusted, of course, if the LED has more color, which may allow it to play a much more useful.

Intelligent Home Furnishing inside smart bulbs is a very basic, but very important part, if the product itself extends from here, this will make the whole intelligent Home Furnishing more complete industrial chain, we now need a smart Home Furnishing, Wulian state to a very high degree of support, otherwise you will lose the things meaning, lose the significance of intelligence. Smart home manufacturers should think is that if the product of the United States, rather than the same thing inside the product.

For more information about LED, please click on China LED network or pay attention to WeChat public account (cnledw2013).